Product image from the manufacturer or its official distributor, reproduced to identify the model (legal notice).
SV07 Plus
The Sovol SV07 Plus is a FDM 3D printer released in 2023 by Sovol, with a build volume of 300×300×350 mm and MSRP of €499. Claimed maximum speed: 500 mm/s.
Manufacturer's suggested retail price (MSRP). Not the store price — the actual price may vary.
Our take on the SV07 Plus
The SV07 Plus was Sovol's option for people who need volume without the price jump: 300 × 300 × 350 mm, a nozzle up to 300 °C, a claimed 500 mm/s top speed and a dual-gear direct-drive extruder. It runs Klipper and is controlled from the browser with Fluidd, so it will appeal to people who enjoy tuning their machine.
Its home turf is large one-piece prints — cosplay helmets, planters, boxes — without having to split them. If you need even more room, the Elegoo Neptune 4 Max goes up to 420 × 420 × 480 mm; if printing ABS or ASA matters more, an enclosed machine like the QIDI Q2 is the alternative to look at.
A heads-up before you go looking: when we checked Sovol's site (October 2026), its official page already redirected to the SV06 Plus ACE, so you'll probably only find it as leftover stock or second-hand. That's also why some figures on its sheet show as unconfirmed: there's no longer an official source to check them against. It has no multicolour or enclosure either, and on a 300 × 300 mm bed large ABS parts tend to warp in open air.
Written from its specs and the sources cited at the end of this page; we haven't tested it in person.
Technical specifications
| Technology | FDM |
|---|---|
| Build volume | 300×300×350 mm |
| Weight | 13 kg |
| Max speed | 500 mm/s |
| Max acceleration | 12,000 mm/s² |
| Max nozzle temp | 300 °C |
| Nozzle material | — |
| Drive | direct |
| Flow rate | — |
| Max bed temp | 100 °C |
| Bed material | PEI plate |
| Auto-leveling | auto mesh |
| Enclosed | No |
| Heated chamber | No |
| AMS compatible | No |
| WiFi | Yes |
| Camera included | No |
| Official slicer | OrcaSlicer (Sovol fork) |
| OrcaSlicer support | Yes |
| Power | 600 W |
| Noise | — |
What materials can the SV07 Plus print?
This comes from four facts on its spec sheet: the nozzle reaches 300 °C, the bed 100 °C, and the machine is open-frame with a direct-drive extruder. Those four facts decide most of the list: nozzle temperature sets the ceiling on what you can melt, the bed decides whether the first layer sticks, the enclosure keeps large parts from warping, and the extruder type rules flexibles. We don't test the machine — this is guidance derived from verified data, not a guarantee.
In short: it prints PLA, PETG, TPU (flexible) without a fight, and it can reach ABS, ASA, Nylon (PA), Policarbonato (PC) with conditions — the detail for each is below.
| Material | Prints it? | Why |
|---|---|---|
| PLA | Yes | Yes. PLA has no special needs: any FDM printer like the SV07 Plus prints it out of the box. |
| PETG | Yes | Yes. With a nozzle up to 300 °C and a bed up to 100 °C it comfortably meets PETG's needs. |
| TPU (flexible) | Yes | Yes. It has a direct-drive extruder, ideal for flexibles; prints TPU well (go slow). |
| ABS | With caveats | With caveats. It reaches 300 °C, but it's open-frame: ABS can warp and ventilation is advised. Doable in a draft-free spot or by adding an enclosure. |
| ASA | With caveats | With caveats. It reaches 300 °C, but it's open-frame: ASA can warp and ventilation is advised. Doable in a draft-free spot or by adding an enclosure. |
| Nylon (PA) | With caveats | With caveats. It reaches 300 °C but is open-frame; Nylon warps in drafts and absorbs moisture. Enclosure + drying almost mandatory. For carbon-fibre variants, use a hardened-steel nozzle. |
| Policarbonato (PC) | With caveats | With caveats. It has the temperature (300 °C) but is open-frame; PC warps badly without an enclosure. Only with one added. For carbon-fibre variants, use a hardened-steel nozzle. |
Need the materials it struggles with? These printers handle them
ABS, ASA, Nylon (PA), Policarbonato (PC)
Popular comparisons
Own the SV07 Plus? Write a review
User opinions, moderated before publishing. hotend doesn't verify purchases.
Sources & references
Specs cross-checked against these public sources:
- 3DWithUs — Sovol SV07 Plus review (volumen, 300 °C, 500 mm/s, Klipper)Independent reviewretrieved10/6/2026
Specs taken from the sources cited above; we have no recorded date for the last check. Confidence in the data: medium.